Quantcast
         
 
 

     

   

             

     TX Organic Research Center

 

 

CURRENT MOON
 
Bed Preparation
 

Bed Preparation 2011 Update

The Key To Successful Gardening is Excellent Bed Preparation

FIRST THE DONíTS:
 
Donít remove native soil
unless drainage problems are caused by the raised beds. Existing native soil is an important part of the bed preparation mix. Donít use peat moss, pine bark or washed concrete sand. These products are problematic, especially when compared to the natural organic choices. Donít till wet soil. Tilling, forking or digging holes in wet soil does damage by squeezing the soil particles together, causing glazing and eliminating the air spaces needed for healthy soil life. Donít spray toxic herbicides. Spraying toxic herbicides anytime is a bad idea, but in the winter, itís really stupid because it canít kill dormant grasses and weeds. 

NOW THE DOíS:
   
Remove unwanted vegetation wisely. Scrape away any existing weeds and grass and toss that material into the compost pile or replant the sod elsewhere. Always remove the grass before any tilling is done. Tilling first drives the reproductive part of the grasses and broadleafs down in the ground to be a weed problem forever. Organic herbicides can be used in the summer, but physical removal is still better.

Raise the beds. Walls arenít essential, but the top of the beds should be flat and higher than the surrounding grades with sloped edges for drainage. This lifting happens naturally if proper amounts of amendments are added to the native soil.   

Add amendments. Add 4 - 6Ē of compost, dry molasses or other organic fertilizer (2 lbs. per 100 sq. ft.), zeolite (10 lbs. per 100 sq. ft.), lava sand (10 lbs. per 100 sq. ft.),  greensand (4 lbs. per 100 sq. ft.), and whole ground cornmeal (2 lbs. per 100 sq. ft.). If the budget allows, add Ĺ inch of decomposed granite. Rototill or fork to a total depth of 8Ē.  

Moisten beds before planting. Planting beds should be moistened after being prepared and before the planting begins. They should be moist but not sopping wet. Do not plant in dry soil because the young roots will dehydrate quickly as they try to grow. The roots of any transplants should be sopping wet and thoroughly hydrated.

Bare root plants. Pot-bound plants can resist water and cause the growth of deformed and unhealthy root development. Soak root balls in water for at least 30 minutes or until they are thoroughly saturated. Remove most if not all of the soil and synthetic fertilizer pellets. Spread the roots out naturally radiating and then cover them with prepared bed soil. If you donít want to go the bare root route, dip plant balls into water and install sopping wet root balls into moist beds. Add  Garrett Juice and Bio S.I. to the water for best results.  

Plant high. Make sure the trunk flares are uncovered by removing excess soil. Set the plants high with the top of the rootballs slightly higher than the surrounding soil and the trunk flare dramatically high and visible. This is especially critical on woody plants. Setting the plant too low can cause poor growth or drowning. 

Mulch beds after planting. Add 2 - 3Ē of organic mulch after planting. Use shredded native tree trimmings for trees, shrubs and ground cover, and a thinner layer of compost for annuals and perennials. Never pile mulch onto the stems of plants. 

The short hand explanation - just add plenty of compost, rock minerals and molasses into the native soil and mulch all bare soil after planting plants with thoroughly hydrated roots.

Azalea bed prep. Mix 50% shredded hardwood bark, cedar or shredded coconut fiber with 50% finished compost. Add a 5 gallon bucket of lava sand and a 1 gallon bucket of greensand per cubic yard of mix. Thoroughly moisten the mixture prior to placing it in the bed - very important. Excavate 3Ē and place 15Ē of the above mix onto the beds. The entire mixture can be put above ground if it doesnít block drainage. If it needs to be lowered, remove as little of the existing soil as possible. The top of the bed should be flat and the sides sloped at a 45 degree angle.  



Q:  I wish to remove all bermuda grass with sod cutter. How do I kill al remaining grass roots, to prep for flower garden.

A:  Roots of the grass do not have to be removed. Only the stems, rhizomes and stolons have reproductive ability. Do not till first, that drives the reproductive pieces into the ground and causes a long term weed problem. Scrap or set the sod cutter t depth of 1/2 to 2" and throw that material in the compost pile. Mixed with leaves and other materials the grass will be ill by the composting process. Next mix in all the organic amendments. Here's the detailed description of that from the web site.

 

 

 

 



Updated 1/11


Previous Question | Back | Next Question
 
 
Printable Version | Back to Top

 
EcoSafe
 
Green Sense Products
 
Farmers Market Soaps
 

H A N N A H ' S    M A R K E T P L A C E

Send this website to a friend Make this website your home page